?
感光變色粉Photosensitive variable toner
一、感光變色原理Principle of photosensitive discoloration：
感光變色產品，經陽光/紫外線照射后，吸收陽光/紫外線的能量面產生顏色變化，當失去陽光/紫外線照射時，即回到原來的顏色。
Photosensitive color products, after/ultraviolet sunlight, absorb sunlight/uv energy surface produce change color, when losing/ultraviolet sunlight, or return to the original color.
?
1.光變粉是隱影印花的典型代表，光是紡織品上的印花圖案隨外部條件的變化而改變色澤的印花，使織物上圖案色澤由常規的“靜態”變?yōu)樾路f奇特的“動態”，其色澤的變化一般為可逆變化。
Light powder, it is a typical representative of the implicit photocopy flowers, light textile printing design along with the changes of external conditions on change the printing color, make the fabric pattern on colour and lustre by conventional "static" into novel peculiar "dynamic", its colour and lustre is usually reversible changes.
2.光敏變色印花亦稱光變色印花，早期的光敏變色印花是用光變?nèi)玖?，在紫外線的照射下染料結構發生變化，呈現不同的色澤。例如，染料Ａ是無色的，經紫外線照射后，分子開環變成菁結構的染料Ｂ，呈藍色，當染料Ｂ再暴露于可見光中又會重新轉變?yōu)闊o(wú)色的染料Ａ?，F(xiàn)在采用微膠囊技術把光變?nèi)玖习灿谀z囊中，一般粒徑為１～１０微米，用微膠囊包覆后的光變?nèi)玖?，其耐光牢度大大提高。目前光變?nèi)玖弦寻l(fā)展到有４個基本色：紫色、藍色、黃色、紅色，這４種光變?nèi)玖掀涑跏冀Y(jié)構均為閉環型，即印在織物上沒有色澤，但在紫外光線照射下可以變成紫色、藍色、黃色、紅色。所謂光敏變色從一種色澤變?yōu)榱硪环N色澤，是在印花色粉中把光變?nèi)玖虾鸵话闵苛掀椿旌蟆鹩』ā＠缬霉庾內玖霞t與涂料藍拼混后印花，在織物表面呈現藍色，在紫外光照射下則變?yōu)樗{(lán)紫色。
光變粉
Early light which is also called light color printing, color printing photosensitive color printing is light dye, dye under uv irradiation structure change, present different color. Dye, for example, is A colorless, after uv irradiation, the molecule open loop into cyanine dye B structure, A blue, when the dye B then exposure to visible light again into A colorless dye. Now using microcapsule technology to optical variable dye coating in the capsule, the average particle size of 1 ~ 10 microns, use after microcapsule coated optical variable dye, the light fastness is greatly?
3.感光SMC粉為感光變色材料產品，變色原理為吸收特定波長之紫外光源，藉由該光源之能量而產生顏 色變化（變?yōu)樽仙?、紅色、蘭色、黃色等），當特定波長的紫外光源不在時，即回復原來的顏色。感光MC粉是經由微膠囊技術處理過的產品，外觀為粉狀，粒徑在1~10μm之間，并具有耐高溫、 抗氧化等微膠囊所改質的特性。感光MC粉可應用于涂料、粉、塑料各產業，產品之設計大多以室內（無紫外光之環境）與室 外（有紫外光之環境）有顏色變化為訴求。
Photosensitive powder for photosensitive color material of SMC products, change color to absorb certain wavelengths of uv light source, by the light of the energy produced by yan color change (into purple, red, blue, yellow, etc.), when a particular wavelength uv light source is not, returns to the original color. Photosensitive MC powder is processed via the microcapsule technology products, appearance is powdery, grain size between 1 to 10 microns, and high temperature resistance, resistance to oxidation and so on microcapsule by a modified characteristic. Photosensitive MC powder can be used in coating, powder, plastic industry, most of product design for indoor environment (no uv light) and room have uv light (environment) has a color change to appeal.
?
?
4.感光基本色：MC系列：紅、黃、藍、紫、天藍、橙、灰、綠
?????????????? SMC系列：紫紅（玫瑰紫） 朱紅（石榴紅） 大紅（胭脂紅） ?橘紅 （桔子紅） 天空藍? 水仙黃? 海藍 橄欖綠? 桃紅? 咖啡灰
?有色變有色：黃變紅? 黃變綠 黃變橙? 黃變紫 藍變紫
Photosensitive basic colors: red, yellow, blue, purple, sky blue, orange, grey, green
Purple, scarlet red orange
Color change of color: yellow to become red Yellow, green, yellow orange Yellow purple blue purple
＃12紫色，＃14蘭色，＃16黃色，#12紫色＃19紅色（無色變有色）
感應波長：#12紫色：290nm~390nm ＃14蘭：280nm~390nm ＃16黃色：270nm~370nm #17 橙色：270nm~370nm ＃19紅色：290nm~400nm 一般紫光燈為365 nm波長所以對黃色和橙色感應不明顯
Blue, purple # 12, # 14 # 16 yellow, purple # 12 # 19 red (colorless color)
Induction wavelength: purple # 12:290 nm to 390 nm # 14:280 nm to 390 nm # 16 yellow: 270 nm to 370 nm # 17 orange: 270 nm to 370 nm red # 19: general light is 290 nm to 400 nm 290 nm wavelength so on induction of yellow and orange is not obvious
?
?
二、塑料射出及押出之應用The application of plastic injection and extruding：
可適用于各種塑料之加工，如PP、PE、PVC、PU、PS、ABS、TPR、EVA、Nylon、Acrylic等,?建議塑料之熔融指數（MI值）大于10，彎曲彈性系小于13000。?加工時應先用白蠟油將塑膠料潤濕。
（注意白蠟油添加量不要超過塑膠料的2％），然后再將變色粉?加入到塑膠料里面攪勻，攪拌時需注意分散性，分散不良可加入適量分散劑?？膳c不同色粉混合使用，搭配出更多樣的色彩變化。應盡量避免在250℃以上之制程進行加工
。感光的光疲乏性產生，由UV光過度曝曬、酸、自由基（單態氧原子）和濕度造成，一般建議不要長時間暴曬。
?
Can be applied to all kinds of plastic processing, such as PP, PE, PVC, PU, PS, ABS, TPR, EVA, Nylon, Acrylic, etc., Suggestions of plastic melt index (MI) is more than 10, bending elasticity is less than 13000. Process should be the plastic material with white wax oil wetting.
(note that white wax content not more than 2% of plastic), and then add the variable toner stir into the plastic material and must be noticed when mixing dispersion, dispersion bad dispersing agent can be added. Can be used mixed with different pigments, match a more diverse color changes. Should try to avoid in the process carry on the processing of above 250 ℃
. Photographic light fatigue sex, by excessive exposure to UV light, acid, free radicals (singlet oxygen atoms) and humidity, generally is not recommended for a long time exposure.
?
?
?
三、產品使用注意事項Products use matters needing attention：
應避免與紫外光吸收劑同時使用、對極性之敏感度高，添加不同之添加劑或使用不同之基材，均可能會造成色差。
Should avoid used in conjunction with ultraviolet absorbent, high sensitivity to the polarity, adding different additives or use different base material, may be the cause of color difference.
?
感光變色粉耐溫度最高為220度，160-180度為宜
感光變色粉的注塑比例為5‰-8‰
感光變色粉適用的材質：PP/PVC/ABS/EVA/硅膠等
注塑用料：透明、半透明白料效果比較好，注塑不可用白料，否則顏色會很淡。
注塑有顆粒的解決辦法：1、分散不開應攪拌均勻 2、加分散劑
Photosensitive resistance change toner temperature up to 220 degrees, it is advisable to 160-160 degrees
Photosensitive variable toner injection ratio of 5 ‰ 8 ‰
Photosensitive variable pigments applicable material: PP/PVC/ABS/EVA/silica gel, etc
Injection material: transparent, translucent, white material effect is better, injection molding, not with white material, otherwise the color will be very weak.
?
?
光變粉MC/SMC/TOP系列，MC有紅、黃、藍、紫、橙、綠、天藍、灰，SMC粉有大紅、朱紅、紫紅、橘紅，TOP粉有紅、黃、藍、紫。
Light powder MC/SMC/TOP series and MC have red, yellow, blue, purple, orange, green, sky blue, grey, SMC powder has a bright red, scarlet, purple, orange, TOP powder has red, yellow, blue, and purple.
?
四、毒性與安全性Toxicity and safety：
感光MC粉對皮膚無刺激性，不含對人體有害的物質，符合安全玩具和食品包裝標準。
Photosensitive MC powder for skin, do not contain harmful substances, toys and food packaging conform to safety standards.
?
五、感光儲存Photographic storage：
感光MC粉應密封儲存于密閉、干燥、陰暗處，避免陽光直射。?
Photosensitive storage:
Photosensitive MC powder should be stored in an airtight sealing, dry, shade, avoid direct sunlight. ?
?
?
六、感光成品介紹Photographic product introduction：
感光變色T恤、光變飛盤、光變發夾、光變鏡片、光變飾品等等
Photosensitive color T-shirt, frisbee, light change hairpin, optical lenses, optical variable ornaments and so on
?